#381
|
||||
|
||||
Design Count Update
529...
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#382
|
||||
|
||||
New Design -- Larkspur
This one just jumped off the board and flew in the simulations without a hitch. This is one for the prototype stage.
Length: 26.63" Diameter: 1.04" (ST-10) Fin Span: 7.54" Weight: 2.92 oz Averaged summary after 10 flights: C6-5......652'......Dv 4 - 12 FPS......48" x 3/16" rod Enjoy!
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#383
|
||||
|
||||
New Design -- Nightwind
One of the earlier sketches finally simulated.
Length: 27.05" Diameter: 0.908" (ST-8) Fin Span: 8.91" Weight: 1.43 oz A8-3.......216'......Dv 5 FPS.......36" x 1/8" rod B6-6.......585'......Dv 28 FPS......36" x 1/8" rod C6-7......1346'......Dv 8 FPS.......36" x 1/8" rod* Enjoy! *Note: I think this altitude figure is a bit optimistic. It's going to take building one and watching it fly before I'm convinced... Addendum: This design has most of the weight off to one side (top) of the thrust line, so there needs to be some offset in the motor tube. I will try to figure out what the angle needs to be, and try to create some centering rings to build this in.
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 Last edited by CPMcGraw : 12-26-2008 at 06:32 PM. Reason: Real rocket science at work... |
#384
|
||||
|
||||
Design Count Update
531...
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#385
|
||||
|
||||
What's going to keep Nightwind from doing the St. Louis Arch maneuver? There's a lot of off-center weight there...
__________________
NAR # 115523 Once upon a better day... SAM #0076 My site: http://rocketry.gonnerman.org |
#386
|
||||
|
||||
Quote:
It will probably be a combination of additional fin area to the opposite side, and some thrust vectoring in the motor tube. It's not going to fly as intended the way it comes fresh out of RS. That's the drawback to these asymetrical models. I am told, however, that RockSim Pro is capable of handling this type of calculation. I'm just not willing to spend $1000 for it.
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#387
|
||||
|
||||
New Design -- Terra Nova Probe
This is another from the 30 sketches that has now been worked up in R9.
Length: 28.70" Diameter: 1.04" (ST-10) Fin Span: 7.15" Weight: 2.11 oz Averaged from 10 simulation runs: C6-3......489'......Dv 13-14 FPS......36" x 1/8" rod Enjoy!
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#388
|
||||
|
||||
New Design -- Stardust
This one is supposed to be a Schoolyard Sounder, but the performance is a bit higher than anticipated. It has high Dv numbers, so use the streamer I'm calling out.
Length: 21.125" Diameter: 1.04" (BC-760) Fin Span: 4.26" Weight: 1.07 oz A10-0T / A3-4T..........868'......Dv 45 FPS......36" x 1/8" rod A10-0T / 1/2 A3-4T......586'......Dv 25 FPS......36" x 1/8" rod Enjoy!
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#389
|
||||
|
||||
Design Count Update
533...
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#390
|
||||
|
||||
Revised Plan -- Rogue Star
Here's one from the beginning of the Designer's Studio thread. The original idea was for the small fins at the rear to be mounted on the pods, canted outward. RockSim 8 could not handle this, but 9 can. It still doesn't know how to render the French Curve scallop on the large body tube, sad to say.
R9 spotted a stability issue with this version that did not show up on the original. The revised plan should be OK. Length: 23.30" Diameter: 1.34" (ST-13) Fin Span: 11.44" Weight: 1.97 oz B4-4......330'......Dv 14 FPS.......36" x 1/8" rod B6-4......338'......Dv 8 FPS........36" x 1/8" rod C6-5......772'......Dv 6-9 FPS......36" x 1/8" rod Enjoy!
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
Thread Tools | Search this Thread |
Display Modes | |
|
|