#1
|
||||
|
||||
New Design -- Vaquero
Apparently I'm obsessed with my ST-13 upscale of the Centuri Chuter-2. Here's a variation that I think is Just Too Cool.
From the attached RockSim 8 file: "Vaquero" is Spanish for "cowboy." Uses 3/4 of fin set for 1.48X Centuri Chuter-2. Deployment velocity is in chute-shredding territory on a C6-5. Reef the chute or substitute a large streamer... maybe 2" wide by 20" long (?) folded in the middle. "Danger, Will Robinson!" --Better use a 48" guide when launching on an A8-3, since it's not stable until it's 30" up the rod. (I also wonder about the need for a second launch lug up on the payload section... ) Now if Carl will just fire up CorelDraw and his other-worldly Krellvinator (sp.?)... Maniacal laughter ensues. .
__________________
Jay Goemmer "Centuri Guy"/"Tau Zero" YORF Member 28 Semroc SAM #0029 NAR 86131 "I think about organizing things all the time. Never seems to happen. I find something that piques my interest and I'm off on a quest. Or a Centuri. " --Bill Eichelberger, 02/22/2022 “Centuri fret buzz in an updated form.” Bill “Wallyum” Eichelberger re: Estes Flutter-By 03 Sept 2014 Last edited by CenturiGuy : 03-11-2009 at 12:32 AM. |
#2
|
||||
|
||||
A Vaquero designed by a Goemmero! Nice!
MarkII
__________________
Mark S. Kulka NAR #86134 L1,_ASTRE #471_Adirondack Mountains, NY
Opinions Unfettered by Logic • Advice Unsullied by Erudition • Rocketry Without Pity
|
#3
|
||||
|
||||
Quote:
Bah! I would only worry if it needed 36.5" of rod to reach a safe speed. If it really needs more than 36", then you had better change that lug to 3/16", because it can be hard to find a 48" long 1/8" diameter rod that won't whip. Quote:
Mandatory in the event that you put anything in that payload section. Otherwise? Well...the lug on the fin is a long way down there. Putting it there, and having it be the only lug on the rocket means that you are asking the fin and fin root to mechanically lever the rocket into alignment with the rod (for 30" of travel, no less). That's a lot to ask of a 3/32" thick balsa fin that is attached with a 1.5" long root. If the rod has to be angled into the wind for any reason, I could see the resulting torque easily breaking the fin or ripping it off. I don't think that you want the Vaquero to fly as a 2FNC. When it is flown with engines that get it up to speed quickly before it has ridden very much of the rod, this will probably not be much of a problem. With lower thrust engines that cause it to need ever more rod guidance, it becomes a greater danger. I would put a small 3/8" long luglet right at the base of the payload section, right above the joint of the payload tube and the lower transition. If you are concerned that this will spoil those smooth, "candy shop cowboy" lines, then you could also put the lug onto a sleek, sculpted standoff just below the lower transition, shaped so that it sort of "flows" into the transition. Or else launch the Vaquero from a tower. Quote:
Shouldn't that be "the alien-tecnology Krellvinator®™ (pat. pending)?" Quote:
Ex-cell-ent...! [evil grin] MarkII
__________________
Mark S. Kulka NAR #86134 L1,_ASTRE #471_Adirondack Mountains, NY
Opinions Unfettered by Logic • Advice Unsullied by Erudition • Rocketry Without Pity
|
#4
|
||||
|
||||
Vaquero, Version 2
Quote:
Quote:
Here's version 2 of the Vaquero, with suggested bigger launch lugs, as well as another lauch lug standoff mounted forward on the ST-10 lower body tube. <big evil grin> The first four sims are in RS8 "before" the modification. The last four are in RS9. .
__________________
Jay Goemmer "Centuri Guy"/"Tau Zero" YORF Member 28 Semroc SAM #0029 NAR 86131 "I think about organizing things all the time. Never seems to happen. I find something that piques my interest and I'm off on a quest. Or a Centuri. " --Bill Eichelberger, 02/22/2022 “Centuri fret buzz in an updated form.” Bill “Wallyum” Eichelberger re: Estes Flutter-By 03 Sept 2014 Last edited by CenturiGuy : 09-10-2011 at 05:33 PM. |
#5
|
||||
|
||||
Quote:
You added a launch lug on a standoff, and it goes higher on every engine? Cool!
__________________
John Thro, NAR #84553 SR I was too old when I started! Now I'll *never* become a BAR! |
#6
|
||||
|
||||
Very nice, Jay. That forward launch lug looks like it belongs there. If I didn't know any better, I would have thought that it had been part of the design all along. I have a special fondness for sweet, clean designs like this one. I give it two thumbs up!
MarkII
__________________
Mark S. Kulka NAR #86134 L1,_ASTRE #471_Adirondack Mountains, NY
Opinions Unfettered by Logic • Advice Unsullied by Erudition • Rocketry Without Pity
|
#7
|
|||
|
|||
Quote:
Nice sleek design Jay ..... very nice! Man, Carl's Krellvinator has been spewing out some parts lately .....
__________________
Steve Naquin TRA# 677 L2 NAR# 85518 L2 SAM# 0052 🚀 In Construction: Der Blue Maxx/Minie-Magg 5.5” & Vander-Burn MDRM Clone w/Stickershock23 Custom Decals 🚀 In Paint & Detail: USR Banshee 🚀 In Build Queue: Estes Doorknob w/Vander-Burn Rocketry Upgrade Kit [Sport Decor], Semroc Centurion-F, Semroc Egg Crate 🚀 In Repair: SLS Lil’ Hustler, SLS Aero-Dart 1969 Trim 🚀 Stay Tuned For Fall 2021 Launch Dates |
#8
|
||||
|
||||
Jay's Vaquero, "Mark II"
Quote:
Good luck, buddy!
__________________
Jay Goemmer "Centuri Guy"/"Tau Zero" YORF Member 28 Semroc SAM #0029 NAR 86131 "I think about organizing things all the time. Never seems to happen. I find something that piques my interest and I'm off on a quest. Or a Centuri. " --Bill Eichelberger, 02/22/2022 “Centuri fret buzz in an updated form.” Bill “Wallyum” Eichelberger re: Estes Flutter-By 03 Sept 2014 |
Thread Tools | Search this Thread |
Display Modes | |
|
|