#41
|
|||
|
|||
Semroc Engine Blocks / Thrust Rings - Rocksim Parts
Here are the Semroc engine blocks / thrust ring parts for Rocksim. The defaults part file contained most of these parts. I just added a few additional parts found on the Semroc web-site and followed same formatting as other part files.
This file should be considered as DRAFT until it can be reviewed and validated. Craig will give ok or post as master file. Data for these parts was pulled from Semroc web-site. If any of the parts or data seem inaccurate please let me know. Thanks! ... Bill |
#42
|
||||
|
||||
Bill,
I just looked at my copy of the data file, and I couldn't see that error, either. It's possible that, with so many copies running around here, I might have been using an older data set which contained the error. If I spot something again, I'll post the visual output so you can see what I'm seeing.
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#43
|
||||
|
||||
New Plan -- Starling
This one probably belongs in the Empyria series. Gentle DV numbers, too...
Length: 24.20" Diameter: 1.04" (ST-10) Fin Span: 7.85" Weight: 1.56 oz A8-3......166'......Dv 12 FPS......36" x 1/8" rod B4-4......397'......Dv 7 FPS.......36" x 1/8" rod B6-4......404'......Dv 1 FPS.......36" x 1/8" rod C6-5......864'......Dv 4 FPS.......36" x 1/8" rod Enjoy!
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#44
|
|||
|
|||
Quote:
Craig - no worries! I'm just glad there doesn't seem to be an error. I've documented all the centering ring data from the Semroc website and have started working on the CRDATA file. It may take a day or so, as I start back to work tomorrow. ... Bill |
#45
|
||||
|
||||
Design Count Update
579...
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#46
|
||||
|
||||
New Design -- Night S.H.A.D.O.
From the sketch collection...
RockSim says this bird will fly as-is, but I'm not making any promises. You will need to balance the glider and trim it for a good glide, then mark the CP. Arrange it directly over the CP position on the boost pod before mounting the launch lug hold down to the pod, and a dowel and pylon (not shown) on the bottom of the glider. Length: 19.62" (this will change, depending on the final position of the glider) Diameter: 1.50" (BC-1043) Fin Span: 10.48" Weight: 1.75 oz B4-4......362'......Dv 10 FPS......36" x 1/8" rod B6-4......370'......Dv 5 FPS.......36" x 1/8" rod C6-5......806'......Dv 7 FPS.......36" x 1/8" rod Do not use the A8-3. It doesn't have enough power to get the model moving rapidly enough off the rod. Enjoy!
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#47
|
||||
|
||||
Estes SCAMP 1.36X, 1.68X Upscales
"Now bigger, better, and even Scampier!"
I'm dredging these up from my long-lost and ill-fated "Updated Classic Designs" thread from 2007-ish. Here are the ROCKSIM 8 files (even though you can see they're saved in my RS9 directory). The 1.36X BT-55 upscale is 18mm, while the 1.68X BT-60 upscale has a 24mm mount. To replicate the original paint scheme, paint one fin black, and along with the forward 2" of the 1.36X Scamp's BT-55. For the BT-60 version, paint the front 2.5" black. Enjoy! .
__________________
Jay Goemmer "Centuri Guy"/"Tau Zero" YORF Member 28 Semroc SAM #0029 NAR 86131 "I think about organizing things all the time. Never seems to happen. I find something that piques my interest and I'm off on a quest. Or a Centuri. " --Bill Eichelberger, 02/22/2022 “Centuri fret buzz in an updated form.” Bill “Wallyum” Eichelberger re: Estes Flutter-By 03 Sept 2014 |
#48
|
||||
|
||||
Design Count Update
582...
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 |
#49
|
|||
|
|||
Semroc Centering Rings - Rocksim Parts
Here are the Semroc centering ring parts for Rocksim. This file should be considered a DRAFT until it can be reviewed and validated. Craig will give ok or post as master file.
Data for these parts was pulled from the Semroc web-site. If any of the parts or data seem inaccurate please let me know. While importing and validating this file, I uncovered an issue with the import process. It appears that the material field entries much match capitalization for the part to imported correctly. If not the part is imported with an incorrect material. For example if the entry is "balsa" and not "Balsa" the part gets imported with the first entry in material database CSV (which is usually "G10 PML...".) I'm including updated files with validated material spelling to resolve this issue. Thanks! ... Bill |
#50
|
|||
|
|||
Semroc Launch Lugs - Rocksim Parts File
Here are the Semroc launch lugs for Rocksim.
This file should be considered as DRAFT until it can be reviewed and validated. Craig will give ok or post as master file. Data for these parts was pulled from Semroc web-site. If any of the parts or data seem inaccurate please let me know. Thanks! ... Bill |
Thread Tools | Search this Thread |
Display Modes | |
|
|