|
|
#71
06-08-2008, 07:34 AM
|
||||
|
||||
Quote:
(Overdubbed monotonic metallic-synthisized voice) By your command...
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635 
|
|
#72
06-10-2008, 07:16 PM
|
|||
|
|||
Lookin' Good
Looks Great Craig. Looks like you have put thay set for French Curves to work. I hope you are not as disapointed in the 13mm motor performance as I have been
 . Best of luck with the test flight and looking forward to you report.James Pierson NAR# 77907
|
|
#73
06-10-2008, 07:30 PM
|
||||
|
||||
|
Quote:
It flew great, on both A10 and A3 power. Go check out the videos in the Flight Report. I'm more than pleased with the results,
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635
|
|
#74
06-11-2008, 11:59 PM
|
||||
|
||||
|
Original "Battlestar Galactica," anyone?
Quote:
   Cool design, too, Craig.  So that just *looks* like a two-stager, eh?  Cheers,
__________________
Jay Goemmer "Centuri Guy"/"Tau Zero" YORF Member 28 Semroc SAM #0029 NAR 86131 "I think about organizing things all the time. Never seems to happen. I find something that piques my interest and I'm off on a quest. Or a Centuri. "--Bill Eichelberger, 02/22/2022 “Centuri fret buzz in an updated form.” Bill “Wallyum” Eichelberger re: Estes Flutter-By 03 Sept 2014
|
|
#75
06-12-2008, 02:00 PM
|
||||
|
||||
|
Quote:
Made me look... The model is perched on top of a SEMROC Rocket Rack, and the image was cropped just above the rack's base. You're seeing the display post... You should be familiar with the concept of "Post Editing"...
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635
|
|
#76
06-12-2008, 11:09 PM
|
|||
|
|||
|
Good flight Video's
Finally got time to respond with a post
 . CPMcGraw Quote: Quote:
Saw the video's about two minutes after reading your post. Most untimely on my part Craig. Looks like a great design that flies well on the 13mm motors. I am slowly learning to stay away from 13mm power when a design has a high surface drag area like some of my designs like Neptune Lander etc... James Pierson NAR# 77907
|
|
#77
06-14-2008, 10:33 PM
|
|||
|
|||
New Design: Sky Chieftain
Here is a design I have named the Sky Chieftain. This design is just under 30 inches long and flies well on standard 18mm motors. I went with an Upper and an Lower launch lug on this design as it seems to help a little bit with liftoff when the wind picks up.
Enjoy and Thanks Again, JP Sky Chieftain 2 (18mm) Launch guide length: 36.0000 In MOTOR.................MAX. ALTITUDE...........DEP. VELOCITY B4-4..................333.18242 Ft.............12.3799 ft/s B6-4..................341.32874 Ft..............7.8697 ft/s C6-5..................789.22900 Ft..............7.1362 ft/s James Pierson NAR#77907 .
|
|
#79
06-15-2008, 01:03 AM
|
||||
|
||||
Foreigner's "Double Vision?"
Quote:
Quote:
 Cheers,
__________________
Jay Goemmer "Centuri Guy"/"Tau Zero" YORF Member 28 Semroc SAM #0029 NAR 86131 "I think about organizing things all the time. Never seems to happen. I find something that piques my interest and I'm off on a quest. Or a Centuri. "--Bill Eichelberger, 02/22/2022 “Centuri fret buzz in an updated form.” Bill “Wallyum” Eichelberger re: Estes Flutter-By 03 Sept 2014
|
|
#80
06-15-2008, 06:23 AM
|
||||
|
||||
|
Quote:
Nice work, JP. I take it this one has been built and flown?
__________________
Craig McGraw BARCLONE Rocketry -- http://barclone.rocketshoppe.com BARCLONE Blogsite -- http://barclone.wordpress.com BARCLONE Forum -- BARCLONE Forum BARs helping BARs SAM 0044 AMA 352635
|
 |
| Thread Tools | Search this Thread |
| Display Modes | |
|
|
Linear Mode
