#1
|
||||
|
||||
Vintage kit build thread: Impulse Aerospace Check-Six
I'm going to build an obscure one--obscure to me anyway: the Impulse Aerospace "Rugged Rockets" Check-Six kit. The instructions read copyright 1997.
Rugged indeed! The BT's appear to be phenolic and are rock-hard (I hope they paint OK.) All parts are accounted for and are in fine shape--including the waterslide decal sheet. I love this recommended motors list! Bye bye! "It's rugged, so it probably landed safely. Somewhere." TBC
__________________
Never trust an atom. They make up everything. 4 out of 3 people struggle with math. Chemically, alcohol IS a solution. NAR# 94042 SAM# 0078 |
#2
|
||||
|
||||
Gosh, I had forgotten about Bill Maness and Impulse Aerospace. Seems they were out of Washington state as I recall. Use to advertise in the Tripoli high power mag; maybe the NAR mag too, but I don’t recall that right off hand.
I don’t have specific memories of this kit, but yes, it looks pretty stout! Earl
__________________
Earl L. Cagle, Jr. NAR# 29523 TRA# 962 SAM# 73 Owner/Producer Point 39 Productions Rocket-Brained Since 1970 |
#3
|
||||
|
||||
Quote:
Yes, out of Washington state.
__________________
Never trust an atom. They make up everything. 4 out of 3 people struggle with math. Chemically, alcohol IS a solution. NAR# 94042 SAM# 0078 |
#4
|
||||
|
||||
Almost time for some booze.
I'll "cut my teeth" on these materials by first assembling the payload and PNC. Using (3) Navy knots (two bowlines and one larks head) I tie the Kevlar tether and small jump ring to the G-10 fiberglass bulkhead of the coupler. I then run a line of 15 minute epoxy around the ID of the coupler tube, feed the Kevlar through the tube, and then center the tube onto the bulkhead and let it rest until the epoxy migrates downward and joins the fiberglass bulkhead to the coupler tube. After the epoxy hardens I lay the coupler/bulkhead assembly onto my Herculean thigh and using the mahogany sanding block I reduce the diameter of the bulkhead until I get a slip-fit into the phenolic payload tube. I then epoxy the coupler assembly into the payload tube. TBC
__________________
Never trust an atom. They make up everything. 4 out of 3 people struggle with math. Chemically, alcohol IS a solution. NAR# 94042 SAM# 0078 |
#5
|
||||
|
||||
Last steps for the night. This ABS PNC is sweet! It has no seam lines at all and it's so hard it feels like medical-grade artificial bone or simulated ivory. The only thing I don't like is that the hole for the wood screw that secures the PNC to the payload tube is very close to the bottom of the PNC's shoulder. Since the will be so close I'll drill a pilot hole.
I first insert the PNC into the payload assembly and trace the location of the hole onto the PNC's shoulder. Using the pin vise I bore a .060" hole into the shoulder of the PNC . This pilot hole should keep the ABS from breaking out--and it works. Oh! Tonight it's NOT Scotch. "The Vixen" has prepared a Black and Tan for me--along with a hot pretzel. Good night. TBC
__________________
Never trust an atom. They make up everything. 4 out of 3 people struggle with math. Chemically, alcohol IS a solution. NAR# 94042 SAM# 0078 |
#6
|
||||
|
||||
Quote:
These were darn near bulletproof. Heh, at the old "Roar at the Shore" in NJ, some would put the biggest motor in them, and you would never see them again.
__________________
Enjoy life, it has an expiration date. |
#7
|
||||
|
||||
Light that thing up on a G-anything, preferably a G138.
__________________
When in doubt, WHACK the GAS and DITCH the brake !!! Yes, there is such a thing as NORMAL, if you have to ask what is "NORMAL" , you probably aren't ! Failure may not be an OPTION, but it is ALWAYS a POSSIBILITY. ALL systems are GO for MAYHEM, CHAOS, and HAVOC ! |
#8
|
||||
|
||||
Really nice build thread, Jeffy!
If I remember correctly the company had almost as many names as kits. Guys, help me here, but I think this company, at various times went by: Seattle Rocket Works, Rocket Vision, Impulse Aerospace, Rugged Rockets, and eventually got sold to Lawn Dart Rocketry. Any history you guys could provide would be great. Kits were the following: Chariot Check-Six Grymm Mach Buster Six-Pack Solar Venture Spit Fire Star Fire They also sold one of the best mid/hi power pads ever produced, the Quad Pod As shown in Jeffy's build thread, parts were VERY robust. Very different from anything else out there. Steve |
#9
|
|||
|
|||
Quote:
Cute little thing I’ll see if I can locate a picture of it
__________________
Steve Naquin TRA# 677 L2 NAR# 85518 L2 SAM# 0052 🚀 In Construction: Der Blue Maxx/Minie-Magg 5.5” & Vander-Burn MDRM Clone w/Stickershock23 Custom Decals 🚀 In Paint & Detail: USR Banshee 🚀 In Build Queue: Estes Doorknob w/Vander-Burn Rocketry Upgrade Kit [Sport Decor], Semroc Centurion-F, Semroc Egg Crate 🚀 In Repair: SLS Lil’ Hustler, SLS Aero-Dart 1969 Trim 🚀 Stay Tuned For Fall 2021 Launch Dates |
#10
|
||||
|
||||
"Grymm"... I like that... Probably describes the prospect of recovery.
__________________
When in doubt, WHACK the GAS and DITCH the brake !!! Yes, there is such a thing as NORMAL, if you have to ask what is "NORMAL" , you probably aren't ! Failure may not be an OPTION, but it is ALWAYS a POSSIBILITY. ALL systems are GO for MAYHEM, CHAOS, and HAVOC ! |
Thread Tools | Search this Thread |
Display Modes | |
|
|