|
|
#61
03-01-2021, 06:21 AM
|
||||
|
||||
Quote:
Bill, Oops! I'll add her to the list.  Bob
__________________
illegitimi non carborundum NAR# 54643 L-1 SAM# 043 AMA# 157091 VRCS# 154 A&P# 42x xx xxxx. 
|
|
#62
03-03-2021, 09:50 PM
|
||||
|
||||
|
Quote:
I got a Cricut a few months ago. One of my first projects was to get a clean set of Enerjet vinyl decals cut. Here is my 1340 (Eliminator kit courtesy of Bill Eichelberger) that sat painted for months and finally got its markings. I also decided against going 29mm. Also shown is a downscale of the Enerjet 2250 to BT60 I did during the shutdown, with BIG decals (I got a little carried away).
__________________
Lee Reep NAR 55948 Projects: Semroc Saturn 1B, Ken Foss Designs Mini Satellite Interceptor In the Paint Shop: Nothing! Too cold! Launch-Ready: Farside-X, Maxi Honest John, Super Scamp
|
|
#63
03-03-2021, 10:19 PM
|
|||
|
|||
|
Quote:
Bunch of weenies.  Attached are pictures of my Enerjet 1340 flown with an AeroTech/Enerjet F67-9W motor at NARAM-60. Yes, I got it back. 
__________________
Bob S.A.M. # 0014
|
|
#64
03-03-2021, 11:47 PM
|
||||
|
||||
|
Quote:
Perhaps you could be so kind as to tell us to where our man cards should be returned. We’re Not Worthy! 
__________________
Lee Reep NAR 55948 Projects: Semroc Saturn 1B, Ken Foss Designs Mini Satellite Interceptor In the Paint Shop: Nothing! Too cold! Launch-Ready: Farside-X, Maxi Honest John, Super Scamp
|
|
#65
03-06-2021, 11:16 AM
|
||||
|
||||
|
Quote:
Thanks. I can't take credit for the outhouse graphic. It's from the Estes decal sheet. I was hoping to paint the Drei Maxx today, but as I look out the window I see it's snowing again. 
|
|
#66
03-06-2021, 11:29 AM
|
||||
|
||||
|
Quote:
Your 2250 really looks great. That Cricut is a handy item to have!
|
|
#67
03-06-2021, 12:37 PM
|
||||
|
||||
|
Quote:
That launch photo has more flat, open ground than my whole zip code. You'd almost have time for a cold one until that bird finally floated back down to sea-level. Impressive! I haven't installed the motor mount yet so technically I don't have to give up my man card. 
|
|
#68
03-13-2021, 01:53 PM
|
||||
|
||||
|
Enerjet 1330
This is my take on the Enerjet 1340. It uses a 3D printed three fin can and the nose from a Mach 12 that has seen better days.
I'm going to fly it with the new Quest composite D20's to give it a little of the original Enerjet flavor.
|
|
#69
03-21-2021, 05:13 PM
|
||||
|
||||
|
Max 2.0
Favorable painting temperatures have returned and my replacement Drei Maxxx is nearly ready to fly.
Construction is almost the same as the original featured in the Quarantine projects thread. This time around I deleted the engine hooks and went with center retention. I also stretched it a little to make more room for the decals. New fins are basswood instead of balsa. My whole fleet basically features bright color catalog paint jobs, so I went a little more vintage this time. I found a pic of an Albatross biplane with flying circus livery and attempted to copy it as best I could. It's still a work in progress, but I'm getting closer and intend to fly it soon.
|
 |
| Thread Tools | Search this Thread |
| Display Modes | |
|
|
Linear Mode
